Loading
Loading
Your feedback directly shapes Sporos.
Sign in to track your feedback history
Browse 1,000 rules and proposed rules from the Federal Register.
1,000
Total Regulations
Showing 961–990 of 1,000
Page 33 / 34
The FAA is superseding Airworthiness Directive (AD) 2022-16- 06, which applied to certain Airbus SAS Model A330-200, A330-200 Freighter, A330-300, and A330-900 series airplanes; and all Model A340- 200 and A340-300 series airplanes. AD 2022-16-06 required modifying the trimmable horizontal stabilizer actuator (THSA) installation, implementing the electrical load sensing device (ELSD) wiring provisions, and installing and activating the ELSD. This AD was prompted by tests that demonstrated that when the upper secondary load path (SLP) of the THSA is engaged, the THSA might not stall, with consequently no indication of SLP engagement, and by the recent determination that the required actions of AD 2022-16-06 cannot be accomplished on certain airplanes. This AD continues to require the actions in AD 2022-16-06 with revised procedures, and also requires additional actions for certain airplanes, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
The FAA is withdrawing a notice of proposed rulemaking (NPRM) that proposed to supersede Airworthiness Directive (AD) 2023-08-04, which applies to certain The Boeing Company Model 787-8, 787-9, and 787-10 airplanes. The NPRM was prompted by reports of a loss of water pressure during flight and water leaks that affected multiple pieces of electronic equipment, and by the discovery that some clamshell couplings did not have the required safety strap. The NPRM would have required inspecting all door 1 and door 3 lavatory and galley potable water systems for missing or incorrectly installed clamshell couplings, inspecting all clamshell couplings for the presence and correct installation of safety straps at door 1 and door 3 lavatories and galleys with a potable water system, and performing applicable on- condition actions. The NPRM would have also prohibited the installation of affected parts at inspection locations and removed Model 787-10 airplanes from the applicability. Since issuance of the NPRM, the FAA has determined that the identified service information may not adequately address the unsafe condition on one of the galleys, and Model 787-10 airplanes should be included in the applicability. Accordingly, the NPRM is withdrawn.
This action establishes United States Area Navigation (RNAV) Route T-553 and amends RNAV Routes T-356, T-358, and T-479 in the eastern United States. This action supports FAA Next Generation Air Transportation System (NextGen) efforts to provide a modern RNAV route structure to improve the safety and efficiency of the National Airspace System (NAS).
This rule amends, suspends, or removes Standard Instrument Approach Procedures (SIAPs) and associated Takeoff Minimums and Obstacle Departure Procedures for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide for the safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
This rule establishes, amends, suspends, or removes Standard Instrument Approach Procedures (SIAPS) and associated Takeoff Minimums and Obstacle Departure procedures (ODPs) for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
The FAA is superseding Airworthiness Directive (AD) 2021-07-13 for certain Pacific Scientific Company rotary buckle assemblies (buckles). AD 2021-07-13 required inspecting each specified buckle including its buckle handle vane and prohibited installing affected buckles. This AD was prompted by the publication of an updated service bulletin, which revises the applicability based on date of manufacture of the affected buckles. This AD retains certain requirements of AD 2021-07-13, reduces the applicability, and requires performing corrective actions by complying with certain portions of the updated service bulletin. The FAA is issuing this AD to address the unsafe condition on these products.
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A319-111, -112, -113, -114, -115, -131, -132, -133, - 151N, and -153N airplanes; A320 series airplanes; and A321-211, -212, - 213, -231, -232, -251N, -252N, -253N, -271N, -272N, -251NX, -252NX, - 253NX, -271NX, and -272NX airplanes. This AD was prompted by a determination that a damage-tolerance and fatigue reassessment of nose landing gear (NLG) repairs is necessary for certain parts fitted on airplanes approved for operation in the Commonwealth of Independent States (CIS). This AD requires repair and replacement of all affected parts, and introduces restrictions for the installation of affected parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 767-200, -300, and -400ER series airplanes. This AD was prompted by a report of multiple engine indicating and crew alerting system messages during potable water servicing after the water leaked onto the electronics equipment cooling air filter. This AD requires installation of hoseducts around the left-side section 43 potable water supply hoses and connections, a potable water system leakage test, and applicable corrective actions. The FAA is issuing this AD to address the unsafe condition on these products.
The FAA is superseding Airworthiness Directive (AD) 2023-09- 01, which applied to all Airbus SAS Model A318 series airplanes; Model A319 series airplanes; Model A320-211, -212, -214, -216, -231, -232, - 233, -251N, -252N, -253N, -271N, -272N, and -273N airplanes; and Model A321 series airplanes. AD 2023-09-01 was prompted by a report that certain overheat detection system (OHDS) sensing elements installed at certain positions might not properly detect thermal bleed leak events due to a quality escape during the manufacturing process. AD 2023-09-01 required a one-time detailed inspection of each affected part installed at an affected position and replacement if necessary and prohibited the installation of affected parts at affected positions. Since the FAA issued AD 2023-09-01, a new airplane model (A321-253NY) has been certified by EASA, on which affected parts could be installed in service. This AD continues to require the actions in AD 2023-09-01, and revises the applicability to include Model A321-253NY airplanes, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
The FAA is superseding Airworthiness Directive (AD) 2022-19- 02, which applied to certain Airbus SAS Model A330-200, -200 Freighter, and -300 series airplanes; and Model A330-841 and A330-941 airplanes. AD 2022-19-02 required revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD continues to require certain actions in AD-2022-19-02, and requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations; as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
The FAA is adopting a new airworthiness directive (AD) for certain Rolls-Royce Deutschland Ltd & Co KG (RRD) Model Trent XWB-97 engines. This AD was prompted by a report of damage to the main fuel hose assembly of the fuel manifold, which resulted an in-flight shut down. This AD requires a one-time set of visual and dimensional inspections of the main fuel hose assembly of the fuel manifold to confirm softness, compliance, and lack of resistance, and for shrinkage, cracks, chafing, dents, kinks, necking, and degradation of the hose braid wire; and, if necessary, replacement of the main fuel hose assembly of the fuel manifold, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
The FAA is adopting a new airworthiness directive (AD) certain Airbus Helicopters Model AS332C, AS332C1, AS332L, AS332L1, AS332L2, AS355E, AS355F, AS355F1, AS355F2, AS355N, AS355NP, AS-365N2, AS 365 N3, EC 155B, EC155B1, EC225LP, SA-365N, and SA-365N1 helicopters. This AD was prompted by a report of an unintentional activation of the hoist shear-button (shear-button) on the collective pitch handle during a night flight. This AD requires checking the operation of the shear- button safety-cap on each applicable collective pitch handle and prohibits installing certain part-numbered collective pitch handles or collective sticks with those part-numbered collective pitch handles installed unless certain requirements are met. The FAA is issuing this AD to address the unsafe condition on these products.
The FAA proposes to adopt a new airworthiness directive (AD) for certain General Electric Company (GE) Model GEnx-1B64, GEnx-1B64/ P1, GEnx-1B64/P2, GEnx-1B67, GEnx-1B67/P1, GEnx-1B67/P2, GEnx-1B70, GEnx-1B70/75/P1, GEnx-1B70/75/P2, GEnx-1B70/P1, GEnx-1B70/P2, GEnx- 1B70C/P1, GEnx-1B70C/P2, GEnx-1B74/75/P1, GEnx-1B74/75/P2, GEnx-1B76/ P2, GEnx-1B76A/P2, and GEnx-2B67/P engines. This proposed AD was prompted by a manufacturer investigation that revealed certain high- pressure turbine (HPT) stage 1 and HPT stage 2 disks were manufactured from powder metal material suspected to contain iron inclusion. This proposed AD would require replacement of affected HPT stage 1 and HPT stage 2 disks with parts eligible for installation. The FAA is proposing this AD to address the unsafe condition on these products.
The FAA proposes to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 757-200, -200CB, and -300 series airplanes. This proposed AD was prompted by a report of cracking found in new locations at a certain body station (STA) during frame segment replacement repairs, including in the web at the K-hole between certain stringers, in the outer chord above the lower hinge intercostal, and in the inner chord and web between certain stringers. This proposed AD would require an inspection or records check for the presence of approved or local repairs, repetitive eddy current inspections for cracking, and applicable on-condition actions. The FAA is proposing this AD to address the unsafe condition on these products.
The FAA proposes to supersede Airworthiness Directive (AD) 2006-20-08, which applies to all Embraer S.A. Model EMB-145, -145ER, - 145MR, -145LR, -145XR, -145MP, and -145EP airplanes. AD 2006-20-08 requires repetitive inspections to detect cracking or failure of the rod ends and fittings of the aileron power control actuator (PCA) and corrective actions if necessary, and provides an optional terminating action. Since the FAA issued AD 2006-20-08, it has been determined that there was an error in identifying a maintenance task number. This proposed AD would continue to require the actions in AD 2006-20-08 and corrects an error in a task number, as specified in an Ag[ecirc]ncia Nacional de Avia[ccedil][atilde]o Civil (ANAC) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
The FAA proposes to supersede Airworthiness Directive (AD) 2023-25-03, which applies to certain Piaggio Aviation S.p.A. (Piaggio) Model P-180 airplanes. AD 2023-25-03 requires a one-time detailed inspection of the horizontal stabilizer (HS) central box for corrosion; an assessment of the corrosion level; and depending on the determination, repetitive detailed inspections of the HS central box for corrosion and the internal composite structure for surface cracks, distortion, and damage; and repair or replacement of the HS assembly. Repair or replacement of the HS assembly is terminating action for the repetitive inspections. Since the FAA issued AD 2023-25-03, it was determined that AD 2023-25-03 imposed an unintended restriction that is not in the mandatory continuing airworthiness information (MCAI). This proposed AD would retain certain actions of AD-2023-25-03 and would remove the unintended restriction. The FAA is proposing this AD to address the unsafe condition on these products.
The FAA proposes to supersede Airworthiness Directive (AD) 2024-19-11, which applies to all Robinson Helicopter Company Model R44 and R44 II helicopters. AD 2024-19-11 requires visually inspecting a certain flex plate assembly (flex plate) and certain clutch shaft forward yokes (yokes), including each flex plate bolt, and depending on the results, taking corrective actions. AD 2024-19-11 also requires removing certain yokes from service within a specified threshold, or as an alternative, performing in-depth inspections. Since the FAA issued AD 2024-19-11, it has been determined that clarifications regarding the alternative inspections are necessary. This proposed AD would retain all the requirements of AD 2024-19-11 and would clarify that the alternative inspections are repetitive and add a particular paint remover option to use when performing those alternative inspections. The FAA is proposing this AD to address the unsafe condition on these products.
This action establishes Area Navigation (RNAV) Routes Q-162 and Q-166 in the southwest United States. The new RNAV routes provide alternative routing for air traffic travelling between southwest Arizona and western Texas in response to severe weather events during the spring and summer months. Additionally, the new RNAV routes expand the availability of RNAV routing in support of transitioning the National Airspace System (NAS) from a ground-based to a satellite-based system for navigation.
This action proposes to revoke Colored Federal Airway Green 6 (G-6) and Alaskan Very High Frequency Omnidirectional Range (VOR) Federal Airways V-459 and V-496 in Alaska. The identifier V-459 is also used for a VOR Federal Airway in California. This action is proposing to revoke the Alaskan V-459, not the V-459 in California. The FAA is proposing this action due to the pending decommissioning of the St. Marys, AK, Nondirectional Radio Beacon (NDB) and the Aniak, AK, NDB.
The FAA proposes to adopt a new airworthiness directive (AD) for certain General Electric Company (GE) Model CF6-80E1A2, CF6-80E1A3, CF6-80E1A4, and CF6-80E1A4/B engines. This proposed AD was prompted by a manufacturer investigation that revealed certain high-pressure turbine (HPT) stage 1 and HPT stage 2 disks were manufactured from powder metal material suspected to contain iron inclusion. This proposed AD would require replacement of affected HPT stage 1 and HPT stage 2 disks with parts eligible for installation. The FAA is proposing this AD to address the unsafe condition on these products.
This action amends Class E airspace extending upward 700 feet above the surface for Presque Isle International Airport, Presque Isle, ME, by adding and updating airport names in the header and geographic coordinates. This action does not change the airspace boundaries or operating requirements.
This action establishes Class E airspace at Webster, SD. This action is due to the development of new public instrument procedures at The Sigurd Anderson Airport, Webster, SD, and supports instrument flight rule (IFR) operations.
This action amends restricted area R-2103A and R-2103B, Fort Novosel, AL, by amending the internal altitude sub-divisions and establishing restricted area R-2103C to match daily mission requirements. These changes do not add additional designated restricted area airspace.
This document delays the effective date of the November 26, 2024 final rule partially granting petitions for reconsideration of a May 9, 2024 final rule that adopted Federal Motor Vehicle Safety Standard (FMVSS) No. 127, "Automatic Emergency Braking for Light Vehicles," which requires automatic emergency braking (AEB), pedestrian automatic emergency braking (PAEB), and forward collision warning (FCW) systems on all new light vehicles.
This action revokes the Class D and Class E airspace in the Republic of the Marshall Islands (RMI). RMI is an independent nation, and the FAA does not have regulatory authority to establish or amend domestic airspace pursuant to Title 14 Code of Federal Regulations (14 CFR) part 71 over RMI's land or territorial waters.
This action amends Class E airspace extending upward from 700 feet above the surface for Kenansville, NC, by adding airspace for ECU Health Duplin Heliport. Controlled airspace is necessary for the safety and management of instrument flight rules (IFR) operations at this airport.
This action proposes to modify the Class D surface area airspace, Class E airspace area designated as surface area, Class E airspace areas designated as an extension to a Class D or Class E surface area, and the Class E airspace area extending upward from 700 feet above the surface of the earth at Bozeman Yellowstone International Airport, Bozeman, MT. These actions would support the safety and management of visual flight rules (VFR) and instrument flight rules (IFR) operations at the airport.
This action proposes to revoke Jet Route J-606 and establish United States Area Navigation Route (RNAV) Q-182 in Alaska. The FAA is proposing this action due to the pending decommissioning of the Chinook, AK, Nondirectional Radio Beacon (NDB).
The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus SAS Model A319-111, -112, -113, -114, -115, -131, - 132, -133 airplanes. This proposed AD was prompted by a widespread fatigue damage (WFD) scenario review for a certification project that indicated several cracks found around the potable water and wastewater service panels were WFD instead of typical fatigue. This proposed AD would require modification of the potable water and wastewater service panels, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
The FAA is revising a notice of proposed rulemaking (NPRM) that applied to all General Electric Company (GE) Model CF34-10E2A1, CF34-10E6, CF34-10E6A1, CF34-10E7, and CF34-10E7-B engines with certain part-numbered high-pressure turbine (HPT) shroud/low pressure turbine (LPT) nozzle assemblies installed. This action revises the NPRM by adding Model CF34-10E5 and CF34-10E5A1 engines to the applicability. The FAA is proposing this airworthiness directive (AD) to address the unsafe condition on these products. Since these actions would impose an additional burden over those in the NPRM the agency is requesting comments on this SNPRM.